Constant leaks could need a new toilet seal or other repair parts. Easy to install and built to last, both consumers and plumbers trust our products the most to fix all toilet problems. Need to replace more than one part? Choose from a variety of all-in-one repair kits. Get higher flow capacity from your water supply line to a variety of household appliances. Fill Valve Flapper Flush Valve. Fill Valve Flapper Connector.
Fluidmaster Products Easy to install and built to last, both consumers and plumbers trust our products the most to fix all toilet problems. Fill Valves The fill valve controls the refill of your tank after your flush. View Details. Flappers The flapper is the main seal that holds water in your tank. Flush Valves Flush valves ensure a steady exit of water from your toilet tank.
Alternatively, it can also be caused by water draining into the overflow tube. You see, when the toilet tank fills to its appropriate level, the fill valve or toilet ballcock stops it from running. Turn off the water supply and hold down the flush handle to empty the tank. Remove the flapper by disengaging it from the chain that connects it to the flush handle and unhooking its two ears from the overflow tube.
Take it to the hardware store so you can find an identical replacement. Here are five things that can go wrong with your toilet's fill valve. Float Problems. The fill valve float is what senses when the toilet tank needs to be refilled and lets the valve open. Water Waste. Fill-Valve Clogs. Continuous Running Due to Flapper Problems.
Fill-Valve Leaks. Generally, you should be replacing your toilet fill valve about every 5 years. Cleaning you fill valve Then wash valve with warm soapy water and then rinse with fresh water. Once a year, or if the fill valve will not turn off, remove the cap assembly and inspect for debris in the valve body seat. There is only one place that a toilet fill valve can leak and that is at the fitting that connects it to the tank.
See the information below for instructions on locating it and tightening it. A fill valve that is allowing water to run over the top of the fill tube and down into the tank is not really a leak. The filler valves , no matter how cheap, should last more than three years.
If you frequently see a puddle of water around your toilet, this could be more than a simple leak: You could have cracks in your tank, and the toilet may need to be replaced. You have an old toilet. You feel it wobble. You've had to fix it often. You have a round bowl.
The fill valve is the device that controls the flow of fresh water into the tank of your toilet. It is normally mounted on the left side of the toilet tank, with a tailpiece that extends through the bottom of the tank, where it attaches to a supply tube that runs to a fixture shut-off valve. Shut off the water to the toilet by turning the handle on the shutoff valve clockwise until it stops.
Flush the toilet to remove most of the water in the tank. Loosen the plastic cap on the top of the fill valve: Wrap one hand around the fill valve shaft, then slide it up to push the float cup the large plastic cylinder that slides on the valve shaft up towards the top of the fill valve, and grasp the shaft firmly. It may help to push down on the cap while turning. Lift the cap from the top of the valve and set it aside. The valve seal is inside the cap.
Place a mug or drinking cup upside down over the top of the valve and hold it in place with one hand. Use your other hand to carefully open the shutoff valve by turning it counterclockwise. Water will flow out of the fill valve, into the cup, and then down into the toilet tank.
This flushes any debris from the valve. Now close the shutoff valve by turning clockwise until it stops. Then remove the old fill valve seal from the valve cap. Install the new valve seal, fitting the nipple on the seal over the stainless steel needle in the cap so the nipple goes up into the cap; this should match the orientation of the old seal.
Open the shutoff valve slowly turning counterclockwise until the handle stops. To finish the job, let the valve refill the toilet tank, then flush the toilet, and check the operation of the fill valve. Also, check for any leaks at the shutoff valve. Actively scan device characteristics for identification.
0コメント